瑞发科Norelsys NS1081/NS1068/NS1068X/NS1066/NS1066X数据恢复资料

Sunny

瑞发科Norelsys NS1081/NS1068/NS1068X/NS1066/NS1066X数据恢复资料

第一款USB 3.0 主控芯片NS1066,NS1068系列USB 3.0-SATA桥接控制器于2013年2月荣获USB-IF官方认证。
2013年9月，瑞发科半导体又推出了第二款USB 3.0主控芯片NS1081系列

    天津瑞发科半导体技术有限公司通过USB-IF认证的NS1081系列芯片采用了业界首创的USB 3.0 多通道eMMC的创新架构，其创新方法及高效率RAID技术已获得中国发明专利授权并已申请多国专利。 基于这种架构，NS1081可以实现将双通道8-bit eMMC做成高端USB 3.0 U盘，其容量和速度都在原eMMC的基础上翻倍，读写速度可高达200MB/s。 有别于传统的USB 3.0 U盘直接使用NAND Flash存储器, NS1081为主控的USB 3.0 U盘使用了广泛用于智能手机和平板电脑等移动设备的eMMC存储器。因移动设备对高性能与高可靠性的要求，eMMC使用业界最高品质的NAND Flash存储内核，而且主要由三星、东芝、闪迪、镁光、海力士等原厂直接供货，从而能提供最好的品质与性能保证。因此NS1081 USB 3.0 U盘方案在可靠性与性能上、尤其是在小文件读写性能上远超直接使用NAND Flash存储器的传统USB 3.0 U盘，其方案在USB 3.0业界最具综合竞争力。针对不同存储器厂商推出的不同版本、制程、容量和读写速度的eMMC芯片，NS1081可以全方面支持，无需针对不同型号的eMMC而修改主控固件(Firmware).


Norelsys Shows Innovative USB 3.0 to Multi-channeleMMC/SD/TF Controller NS1081TAIPEI - June 3, 2014 - Norel Systems Limited (Norelsys), a China fablesssemiconductor company that specializes in high-speed mixed-signal and innovative I/Otechnologies, introduced its USB 3.0 to multi-channel eMMC/SD/TF controllerNS1081 series at 2014 Computex Taiwan.Norelsys is the first IC company from mainland China that has received the USBImplementers Forum (USB-IF) SuperSpeed USB (USB 3.0) certification. Certified inFebruary 2013, the company’s USB 3.0 to SATA bridge controllers NS1066 andNS1068 have been in mass production at Lenovo and other major brands. In September2013, Norelsys released its second USB 3.0 controller chip NS1081, targeting bothUSB 3.0 flash drive and USB 3.0 card reader markets. In February 2014, NS1081 seriescontrollers NS1081/NS1081S/NS1081C were awarded the USB-IF USB 3.0certification (TID: 340000107) and Microsoft WHQL certification. Since then,NS1081 series ICs have been in volume production by brand customers and OEMmanufactures.NS1081 employs patented parallel architecture and efficient RAID-0 technologies.When used in a two-channel configuration, NS1081 can double the read/write speedand achieve up to 200MB/s read/write speed.Unlike the traditional USB 3.0 flash drives using direct NAND flash controller IC,NS1081-based flash drives use eMMC chips for storage. The eMMC chips are widelyadopted in smart phones and tablets and are designed to meet the demandingrequirements of mobile devices. The use of eMMC chips allows the NS1081-basedflash drives to achieve a level of reliability and performance not seen in the majority ofUSB 3.0 flash drives. Furthermore, NS1081 supports all types of eMMC chips with aunified firmware, regardless the variations in eMMC semiconductor process, capacityand speed class. There is no complex firmware tuning in the production and test process.NS1081 offers one of the most competitive solutions for USB 3.0 flash drives.In addition to flash drives, NS1081 can also be used as a high-end USB 3.0 card reader.When it is applied to a multi-LUN card reader, two memory cards can worksimultaneously at the SuperSpeed USB data rate. When it is applied to a two-channelRAID-0 card reader, the storage capacity and read/write speed of the card reader aredoubled. NS1081 supports a variety of memory cards, including but not limited toMMC, SD, and microSD (TF), with the storage capacity up to 2TB. NS1081 alsosupports advanced speeds, such as SD 3.0 UHS-I and eMMC 4.5 HS200.Press ReleaseOffered in a small footprint 6x6 QFN48 package, NS1081 integrates a high-efficiency5V to 1.2V DC-DC regulator as well as 5V to 3.3V/1.8V LDO regulators. Togetherwith NS1081, Norelsys also released the single-channel eMMC controller NS1081Sand single-channel card reader NS1081C. NS1081S targets the smaller capacity USB3.0 flash drive applications. NS1081C provides cost savings to customers notdemanding in performance.As a leader in USB technology developments, Norelsys is also developing a USB 3.1transceiver IC operating at 10Gbps. About NorelsysNorel Systems Limited is a fabless semiconductor company headquartered in Tianjin, China andwith sales and support offices in Shenzhen. Norel Systems was founded in 2009 by Silicon Valleysemiconductor veterans and China’s local marketing and sales experts. The company has closed tworounds of investments from Legend Capital, SAIF Partners and Legend Star.The company specializes in the design and development of complex SOC chips requiringhigh-speed mixed signal expertise. With in-house developed PHY IPs covering USB 3.0,SATA1/2/3, PCIe, HD-SDI, HDMI, Displayport, MIPI and Thunderbolt (Lightpeak), NorelSystems is positioned to lead the market in providing turn-key solutions for mobile devices,consumer electronics and PCs.

Sunny

NS1066/NS1066X USB 3.0 to SATA Bridge Controller
Introduction
NS1066/NS1066X is a versatile high-performance and
low power USB 3.0 to SATA bridge controller. On one
side, it interfaces with the USB interface and is compatible
with USB Super-speed (5Gbps), High-speed (480Mbps),
and Full-speed (12Mbps). On the other side, it interfaces
with hard drive or SSD devices through the SATA
interface. NS1066 and NS1066X are pin-to-pin compatible.
NS1066 supports SATA I (1.5Gbps) and SATAII (3Gbps).
NS1066X also supports SATA III (6Gbps).
Block Diagram
USB 3.0
PHY
(compatible
with USB
2.0)
USB
3.0/2.0
Link,
Protocol,
Transport
Layer
FIFO
FIFO
SATA Link,
Transport
Layer
SATA
PHY
3.3V to 1.2V LDO
AND DC/DC GPIO SPI,I²C
SRAM
USB 3.0 SATA
8051
Highlights
 Self-developed high-performance, low-jitter, and
low-power USB 3.0 and SATA transceivers with
built-in test capabilities for guaranteed functions and
performance.
 Integrated adaptive equalization circuit (patent
pending) for the USB Super-speed (5Gbps) receiver
which automatically compensates for the USB 3.0
connector and cable signal degradation.
 Configurable on-chip voltage regulators (patent
pending), pin selectable LDO or DC/DC allowing
users to make trade-offs between power and cost.
 Dedicated LED controllers which provide versatile
LED control functions without the intervention of
8051 MCU or firmware.
Features
 Support USB 3.0 Specification Revision 1.0.
 USB 3.0 adaptive receiver equalization for better and
more reliable Super-speed operation. (patent
pending)
 Support USB Specification Revision 2.0.
 Support USB Super-speed/High-speed/Full-speed
(5Gbps/480Mbps/12Mbps) data transfer rates.
 Support USB Mass Storage Class, Bulk-Only
Transport Specification.
 Support USB 3.0 U0/U1/U2/U3 (P0/P1/P2/P3) and
USB 2.0 L0/L1/L2 power saving modes.
 Support Gen1i/Gen1m/ Gen2i/Gen2m of Serial ATA
Specification Revision 2.6.
 Support Gen3i of Serial ATA Specification Revision
3.0 (NS1066X only).
 Support ATA/ATAPI PACKET command set.
 Support ATA/ATAPI LBA48 addressing mode.
 Support SPI and I
2
C interface for firmware and
Vendor VID/PID customization.
 Support three dedicated LED controllers. Additional
LEDs are supported via GPIO pins and the
customized firmware.
 Support two dedicated Button on/off controllers.
Additional button input functions are supported via
GPIO pins and the customized firmware.
 Support hard drive power down control pin.
 Support 8 GPIO pins.
 The functions of all digital pins, including the Button
in, LED, GPIO and hard drive power down control
pins are programmable by the firmware.
 Support one-button disk backup.
 Support Win7/Vista/XP/2000/Me, Linux and Mac
OS 9.x/10.x.
 25MHz external crystal.
 Integrated 3.3V to 1.2V voltage regulators, pin
selectable LDO or DC/DC. (patent pending)
 QFN48 (6x6) package.

Sunny

NS1068/NS1068X USB 3.0 to SATA Bridge Controller
Introduction
NS1068/NS1068X is a versatile high-performance and low
power USB 3.0 to SATA bridge controller. On one side, it
interfaces with the USB interface and is compatible with USB
SuperSpeed (5Gbps), Hi-Speed (480Mbps), and Full-Speed
(12Mbps). On the other side, it interfaces with hard drive or SSD
devices through the SATA interface. NS1068 and NS1068X are
pin-to-pin compatible. NS1068 supports SATA I (1.5Gbps) and
SATAII (3Gbps). NS1068X also supports SATA III (6Gbps).
Block Diagram

USB 3.0
PHY
(compatible
with USB
2.0)
USB
3.0/2.0
Link,
Protocol,
Transport
Layer
FIFO
FIFO
SATA Link,
Transport
Layer
SATA
PHY
5V to 3.3V LDO
AND 5V to 1.2V DC/DC GPIO SPI,I²C
SRAM 8051
USB 3.0 SATA
Highlights
 Self-developed high-performance, low-jitter, and
low-power USB 3.0 and SATA transceivers with built-in
test capabilities for guaranteed functions and performance.
 Integrated high-efficiency on-chip regulators including a
5V to 3.3V LDO and a 5V to 1.2V DC/DC.
 Compliant with USB bus-powered and self-powered power
consumption requirements. Consume less than 2.5mA in
USB 3.0 and USB 2.0 suspend mode.
 Passed system ESD +/-15kV air-gap discharge and +/-8kV
contact discharge without external ESD protection devices.
Features
 Support USB 3.0 Specification Revision 1.0.
 USB 3.0 adaptive receiver equalization for better and more
reliable SuperSpeed operation.
 Support USB Specification Revision 2.0.
 Support USB Super-speed/High-speed/Full-speed
(5Gbps/480Mbps/12Mbps) data transfer rates.
 Support USB Mass Storage Class, Bulk-Only Transport
Specification 1.3.
 Support UAS Attached SCSI Protocol Specification 1.0.
(customized firmware required)
 Support USB 3.0 U0/U1/U2/U3 (P0/P1/P2/P3) and USB
2.0 L0/L1/L2 power saving modes.
 Fully support USB bus-powered and self-powered power
consumption requirements; consumes less than 150mA in
USB 3.0 U0 mode, less than 100mA in USB 2.0 L0 mode
and less than 2.5mA in USB 3.0 and USB 2.0 suspend
mode. Currents are measured over 5V power supply.
 Support SATA 1.5Gbps and 3.0Gbps data transfer rates.
 Support Gen2i/Gen2m of Serial ATA Specification
Revision 2.6.
 Support Gen3i of Serial ATA Specification Revision 3.0
(NS1068X only).
 Support ATA/ATAPI PACKET command set.
 Support ATA/ATAPI LBA48 addressing mode.
 Support SPI interface for firmware and Vendor VID/PID
customization.
 Support three dedicated LED controllers. Additional LEDs
are supported via GPIO pins and the customized firmware.
 Support two dedicated Button on/off controllers.
Additional button input functions are supported via GPIO
pins and the customized firmware.
 Support hard drive power down control pin.
 Support multi-GPIO pins.
 Support in-system SPI flash programming, for both initial
program and follow-on upgrade via the USB interface.
 The functions of all digital pins, including the Button in,
LED, GPIO and hard drive power down control pins are
programmable by the firmware.
 Support one-button disk backup.
 Support Win8/Win7/Vista/XP/2000/Me, Linux and Mac
OS 9.x/10.x.
 25MHz external crystal.
 Integrated 5V to 3.3V LDO and 5V to 1.2V DCDC voltage
regulators. No external voltage regulator is required.
 QFN48 6x6 package.

james19820515

1066和1068貌似需要1068x_uasp_sata3_3.9.1.9_gpio2.10.img才能支持trim，但是暂时下不到。